DIY

DIY Framed Bathroom Mirrors

May 24, 2018

One of the biggest changes from our bathroom makeover was when we framed our builder-grade mirrors. We were trying to do this bathroom makeover project as inexpensively as we could while still updating the look, and we think framing the mirror and adding some metal accents really improved everything overall while keeping the cost down.

image1 copy

Here is how we did it!

 

Materials

– 4 pieces of 1×4 Knotty Alder wood cut to length

-One extra piece of 1/4″ scrap wood to sit above the mirror to create a flush surface

-miter saw

Stain in color of choice and paper towels or old rags to rub it on. We used THIS stain.

– 4 L brackets– We spray painted ours black

– 8 black screws: we could not find just black screws in the hardware section, so we bought a little kit that included at least 8 black screws, and the whole kit only cost a few bucks, so it was worth it to us.

-Drill with driver bit

-Small drill bit for pilot hole

1 tube of Gorilla Glue Adhesive

Directions: 

Begin by cutting your wood to the length using 45* miter angles.

Stain your wood using paper towels or an old rag. I REALLY wanted an aged look and spent quite a while at Home Depot testing different stains on various woods, and after a LOT of trial and error, we discovered the stain we bought to be the one. (See above.)

 

Once dry, lay out your frame on a flat surface and ensure all angles match up nicely. And if not, try again. Ha!

image5

Then, glue the inside of the corners making sure not to use too much glue so it doesn’t seep out.

image1

Next, center the L brackets on each corner and drill pilot holes before screwing them into place.

image6

Next, place the frame over the mirror to make sure it fits, and then with a dry erase marker, roughly trace the inside of the frame onto the mirror so that you have a guideline for where to glue. Using tight S patterns, apply the Gorilla Glue on the mirror about an inch or so inside the line you made so that when the wood presses against it, it doesn’t squirt out the sides.

image8

Once the glue is on the mirror, place the frame over the glue, make sure it is level, and press firmly until secure. That’s it!

image9

 

image1 copy 2

image5

Thanks for stopping by!

Only registered users can comment.

  1. Ooooh you’re getting me inspired! I have two unframed bathroom mirrors and they’re driving me nuts. I think I have my next home project!!!

  2. Thanks for sharing this. We have the same lights in your before picture in our bathroom and I would like to change out. We also have a big mirror I would like to put a frame on as well.

    1. Can you walk me through what you did with the extra scrap wood?? Did you screw it into studs? Then used gorilla glue for the top? Thanks! Looks stunning and I would love to update ours too!

      1. Oooh I had the exact same question! Do you screw the frame into the scrap wood at the top? Or gorilla glue it on? Is it weird that I’m worried the extra weight of the wood frame will pull the whole mirror off the wall?

        Will check back hoping for a response =D

    1. Hi! This looks great, I’m going to give it a try. Also do you know what color was used to paint your cabinets? I really love that blue gray color and I want to use it. Thank you!

  3. This looks great! I’ve been looking for a new mirror for ours. I think I will try this instead. Thanks for sharing.

  4. I love this idea! What a cool way to transform your bathroom mirror, I really like how industrial it looks, and not to mention your bathroom is amazing!

    ~xo Sheree
    poshclassymom.com

  5. Did you stencil paint the tile, or is that new tile?? I followed your directions and our downstairs bathroom looks incredible!!

  6. I am super curious after some time, has it held up with the moisture in the bathroom? I know Gorilla Glue is tuff but I have trust issues with such a heavy project.

  7. Hi I have plain white cabinets and I could not help but notice and (love) the color of these. Do you happen to know what color they are painted or are they custom? Thanks!

  8. So these many years later is your frame still going strong ? 3 questions
    1. Where did you get knotty Adler wood
    2. Do you see the glue, back side of the frame in the mirror ?
    3. Did you have clips holding your mirror up?

    Thanks

Leave a Reply

Your email address will not be published. Required fields are marked *